WebStep Two: Mix the Mash. Now dump the cracked grains into a 30 gallon container and stir in 25 lbs. of sugar. When the sugar is dissolved completely add 15 to 20 gallons of cold water until the mash mix reaches 30 gallons by total volume. The Super Simple Beginner Corn Mash Recipe. Watch on.
Preview
See Also: Share RecipesShow details
WebJul 7, 2019 · Step Two: Mix the Mash. Now dump the cracked grains into a 30 gallon container and stir in 25 lbs. of sugar. When the sugar is dissolved completely add 15 to 20 gallons of cold water until the mash mix reaches 30 gallons by total volume. Chopped corn with Sweet feed and yeast pack.
WebJan 27, 2024 · Before getting started with your moonshine mash, gather these ingredients: 8 lbs. of cracked corn; 8 lbs. of sugar; 5 gallons of water; 1 packet of distillers yeast; These basic ingredients will lay the foundation for a quality moonshine mash. Directions. Follow these step-by-step instructions for crafting your 5-gallon moonshine mash: 1. Cook
WebStep 1: Cook The Grains. Bring 5 gallons of water to a boil in a pot big enough to hold the water and the grain. Once the water starts to boil lower the heat and add the cracked corn and the sweet feed. Then continuously stir for 30 minutes. Note: If you don't stir continuously you run the risk of letting the grains scorch on the bottom of the pot.
WebNov 6, 2020 · This recipe is reminiscent of the traditional mash created by George Washington’s distillery used to create his Rye Whiskey at Mount Vernon. This rye whiskey mash consists of 60% rye, 35% corn, and 5% barley. For this recipe you will need: 6 Pounds Rye Malt; 3.5 Pounds Flaked Maize (Corn).5 Pound Malted Barley; 5 Gallons of …
WebMar 11, 2024 · Yes, but the recipe is a bit different from what you read above. For 5 gallons of mash, try using 7 lbs. of granulated cane sugar, 5.5 lbs. of cracked corn, and 1.5 lbs. of rye. Add water to get to the 5 total gallons of volume, and stir vigorously for a couple of minutes. Put the mixture into your fermenter, and pitch the yeast.
WebFeb 28, 2015 · To do the pre-mash, you’re going to add 9 pounds of cracked corn to your food-grade bucket (preferably food-grade) and mix in (preferably) 2 gallons of pre-boiled backset. This is basically what’s left over from your previous whiskey wash. If you don’t have this, don’t worry.
WebPut your 3-3/4 gallons of water back into the fermenter so your yeast won't die while you distill. While you're at it, this is a perfect time to scoop the spent corn off the top and replace with an equal volume of newly cracked corn. Later we'll add the 1-1/4 gallons of backset and 7 more pounds of granulated sugar.
WebMay 13, 2022 · Bring the 5 gallons of water to a boil in a large pot. Once the water is boiling, slowly add in the 10lbs of cornmeal while stirring. Once all cornmeal has been added, stir in 1 cup of sugar. Let the mixture boil for 30 minutes, stirring occasionally. After 30 minutes, remove the pot from heat and let it cool for 15 minutes.
WebPlace 6lbs of cracked corn into the fermenter and pour the sugar water over the top. Stir well and leave for about an hour to let the corn steep. Add around 1.5 to 2 gallons of backset from a recent mash for the first generation, and backset from the previous distillation in subsequent generations. Top up with water to make up the 6 gallons.
WebApr 29, 2024 · Heat 5 gallons of mash water up to 165F. Turn off heat when target temperature is reached and stir in the 8.5 pounds of corn. Stir the mash continuously for about 5 minutes then stir for a few seconds every five minutes until the temperature drops to 152F. Once the target temp is met, stir in the malted barley.
WebDec 18, 2013 · Cover the fermentation vessel as the mash cools. Once the mash has cooled to around 80 F or less, add your desired whiskey yeast (I use whiskey distiller’s yeast). Mix the yeast in and cover. Once the fermentation has slowed, pour the contents of the original fermentation vessel through a mesh bag and into a clean fermentation vessel.
Web8.5 pounds of cracked or flaked corn. 1.5 pounds of crushed malted barley. 1. Make the Mash. The process begins by heating 5-gallons of water to 165°F. When the temperature reaches this point, turn off the heat and add the full amount of corn to the water. It’s important to stir the corn consistently for 5 minutes.
WebProducing the mash. Step 1: Boil the 2.5 gallon (10 l) of clean water for about 15 minutes in a large pot and let it naturally cool down to 165°F (74°C). Step 2: Now, add the grains as well as the gypsum and the acid blend. The latter two ingredients are optional and you can play with the dosage.
WebMay 30, 2021 · Pour two gallons of water into a large pot and heat to boiling. Use your cooking thermometer to make sure the heat does not go above 120°F. Add the sugar a few pounds at a time and let it dissolve. Keep adding sugar until all 8 lbs are dissolved. Once the sugar is dissolved add the wash to a fermentation bucket.
WebApr 27, 2021 · After 1 hour, put the contents in a 5-gallon bucket. Add enough hot or cold water to reach the target temperature of 95-100 degrees and to within 1-2 inches from the brim of the bucket. Take a reading with the hydrometer for the specific gravity and make a note of the reading on the grain bill.
WebInstructions. In a large pot, bring 5 gallons (18.9 liters) of water to a boil. Gradually add in 8 pounds (3.6 kg) of cornmeal while stirring constantly to prevent clumps from forming. After bringing the 5 gallons of water to a boil, lower the heat to a gentle simmer and allow the mixture to cook for an hour to ensure proper hydration and