Beef Brisket Recipes Smoker

Smoked Brisket Recipe Traeger Grills

Web4. Place brisket, fat side down on grill grate. Cook brisket until it reaches an internal temperature of 160℉, about 5 to 6 hours. When brisket reaches internal temperature of …

Rating: 4.4/5(131)

Preview

See Also: Brisket RecipesShow details

Smoked Brisket [Best Barbecue Beef Recipe] The …

WebMar 28, 2021 · 4.75 from 4 votes. Incredible smoked brisket cooked low and slow over hickory wood. This classic smoked beef cut is the best …

Rating: 4.8/5(4)
1. Place your brisket on a large cutting board and position it so the flat is on top.
2. Remove any silver skin or excess fat from the flat muscle. Aim to trim it until the fat is smooth between fat and point.
3. Follow by trimming excess fat from the point. Trim the ends of the flat to form a square-like shape.
4. Turn the brisket over and trim the fat cap so that it's only about half a centimetre in thickness across the surface of the meat.

Preview

See Also: Barbecue Recipes, Beef RecipesShow details

Authentic Texas Style Smoked Brisket Recipe

WebDec 4, 2015 · When the meat in this smoked brisket recipe hits an internal temperature of 200 or 205°F (83 or 96°C) in the flat, hold the wrapped …

Rating: 4.7/5
1. Trim. Trim off most of the fat cap but leave about 1/4". Until you get the hang of trimming fat, you might cut off some of the meat in the process. No harm, no foul. Some cooks attempt to remove some of the fat layer between the flat and the point by slicing them apart from both sides, but not slicing all the way through so they remain attached. Go for it, if you like. Either way, when you're done trimming fat, clean the meaty side of any silverskin, a shiny, thin, tough membrane. Set aside some fat for making burnt ends, described below. I always freeze some of the fat and grind it for my burgers if I think the meat needs more fat. I also render some fat over low heat in a pan, and freeze that too. I use beef fat to paint my steaks just before searing.
2. Separate. You can remove the point at this stage, especially if you want to turn it into those luscious chunks of beef candy called burnt ends. Purists cry heresy, but separating the point and flat gives you a flat that is pretty uniform in thickness so it will cook more evenly. Plus, you can apply flavorful rub to all sides of the flat, and you will get an all-around smoke ring. You can cook the point and flat side by side.
3. Inject (optional). I almost always inject briskets with beef broth. This meat takes so long to cook that the extra moisture helps keep it from dehydrating, and the salt helps the meat hold onto moisture and enhances flavor. Use broth only. No need to add spices, juices or other flavorings. All we want here is moisture. We don't want the fluid to mask the flavor of the meat. If you have a hypodermic syringe for injecting meat, now's the time to use it. Pump in about 1 ounce of beef broth per pound of raw meat by inserting the needle parallel to the grain in several locations about 1" apart and backing it out as you press the plunger. Do it in the sink, and be careful so you don't get squirted in the eye.
4. Season. If you have not injected salt, salt the meat about 12 to 24 hours in advance so it can work its way in, 2 to 4 hours minimum. If you have injected a salt solution, do not salt the meat.Notice the direction of the grain of the flat and remember this so you can carve the cooked brisket perpendicular to the grain. The grain will be hard to find under the bark when it is done, so some people mark it with a slice in the surface or cut off a slice to show them the way to cut later. After salting, sprinkle the Big Bad Beef Rub liberally on all areas of the meat and rub it in. Keep the meat chilled until just before you cook it. Chilled meat attracts more smoke. I strongly recommend you use a remote digital thermometer and insert the probe with the tip centered in the thickest part of the meat furthest from the heat.

Preview

See Also: Brisket RecipesShow details

Smoked Brisket Perfect Every Time Vindulge

WebAug 3, 2022 · Preheat Smoker: Set the smoker to 250 degrees Fahrenheit (F) with both lump charcoal and wood. We use fruit woods for brisket for …

Rating: 4.6/5(103)
1. The day before cooking, trim the excess fat off the brisket, apply olive oil. In a separate bowl, combine your dry rub ingredients, and liberally apply to the brisket. Leave in fridge overnight prior to cooking.
2. The day of cooking, preheat your smoker to 250 degrees F, we use fruit wood like apple or cherry.
3. Place brisket on the smoker (using large tongs) when the temperature is a consistent 250 degrees and insert your two zone meat probes. One for the meat inserted into the flat, and one to monitor the ambient temperature of the cooking chamber.
4. When the internal temperature of the brisket is 165 degrees you will carefully remove the brisket and place onto two pieces of pink butcher paper to wrap. Remove the meat probe, tightly wrap the brisket, and then add the meat probe back into the same general area. Place back into the smoker.

Preview

See Also: Brisket RecipesShow details